|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
tip120, tip121, TIP122 npn silicon power darlingtons 1 december 1971 - revised september 2002 specifications are subject to change without notice. designed for complementary use with tip125, tip126 and tip127 65 w at 25c case temperature 5 a continuous collector current minimum h fe of 1000 at 3 v, 3 a b c e to-220 package (top view) pin 2 is in electrical contact with the mounting base. mdtraca 1 2 3 absolute maximum ratings at 25c case temperature (unless otherwise noted) notes: 1. this value applies for t p 0.3 ms, duty cycle 10%. 2. derate linearly to 150c case temperature at the rate of 0.52 w/c. 3. derate linearly to 150c free air temperature at the rate of 16 mw/c. 4. this rating is based on the capability of the transistor to operate safely in a circuit of: l = 20 mh, i b(on) = 5 ma, r be = 100 ? , v be(off) = 0, r s = 0.1 ? , v cc = 20 v. rating symbol value unit collector-base voltage (i e = 0) tip120 tip121 TIP122 v cbo 60 80 100 v collector-emitter voltage (i b = 0) tip120 tip121 TIP122 v ceo 60 80 100 v emitter-base voltage v ebo 5v continuous collector current i c 5a peak collector current (see note 1) i cm 8a continuous base current i b 0.1 a continuous device dissipation at (or below) 25c case temperature (see note 2) p tot 65 w continuous device dissipation at (or below) 25c free air temperature (see note 3) p tot 2w unclamped inductive load energy (see note 4) ?li c 2 50 mj operating junction temperature range t j -65 to +150 c storage temperature range t stg -65 to +150 c lead temperature 3.2 mm from case for 10 seconds t l 260 c this series is currently availabl e, but not recommended for new designs. tip120, tip121, TIP122 npn silicon power darlingtons 2 december 1971 - revised september 2002 specifications are subject to change without notice. notes: 5. these parameters must be measured using pulse techniques, t p = 300 s, duty cycle 2%. 6. these parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts. ? voltage and current values s hown are nominal; exact values vary slightly with transistor parameters. electrical characteristics at 25c case temperatur e parameter test conditions min typ max unit v (br)ceo collector-emitter breakdown voltage i c = 30 ma (see note 5) i b = 0 tip120 tip121 TIP122 60 80 100 v i ceo collector-emitter cut-off current v ce = 30 v v ce = 40 v v ce = 50 v i b =0 i b =0 i b =0 tip120 tip121 TIP122 0.5 0.5 0.5 ma i cbo collector cut-off current v cb = 60 v v cb = 80 v v cb = 100 v i e =0 i e =0 i e =0 tip120 tip121 TIP122 0.2 0.2 0.2 ma i ebo emitter cut-off current v eb = 5 v i c =0 2 ma h fe forward current transfer ratio v ce = 3 v v ce = 3 v i c = 0.5 a i c = 3a (see notes 5 and 6) 1000 1000 v ce(sat) collector-emitter saturation voltage i b = 12 ma i b = 20 ma i c = 3a i c = 5a (see notes 5 and 6) 2 4 v v be base-emitter voltage v ce = 3 v i c = 3 a (see notes 5 and 6) 2.5 v v ec parallel diode forward voltage i e = 5 a i b = 0 (see notes 5 and 6) 3.5 v thermal characteristics parameter min typ max unit r jc junction to case thermal resistance 1.92 c/w r ja junction to free air thermal resistance 62.5 c/w resistive-load-switching characteristics at 25c case temperature parameter test conditions ? min typ max unit t on tu r n - o n t i m e i c = 3 a v be(off) = -5 v i b(on) = 12 ma r l = 10 i b(off) = -12 ma t p = 20 s, dc 2% 1.5 s t off turn-off time 8.5 s tip120, tip121, TIP122 npn silicon power darlingtons 3 december 1971 - revised september 2002 specifications are subject to change without notice. typical characteristics figure 1. figure 2. figure 3. typical dc current gain vs collector current i c - collector current - a 05 50 10 h fe - typical dc current gain 40000 100 1000 10000 tcs120aa t c = -40c t c = 25c t c = 100c v ce = 3 v t p = 300 s, duty cycle < 2% collector-emitter saturation voltage vs collector current i c - collector current - a 05 50 10 v ce(sat) - collector-emitter saturation voltage - v 0 05 10 15 20 tcs120ab t c = -40c t c = 25c t c = 100c t p = 300 s, duty cycle < 2% i b = i c / 100 base-emitter saturation voltage vs collector current i c - collector current - a 05 50 10 v be(sat) - base-emitter saturation voltage - v 05 10 15 20 25 30 tcs120ac t c = -40c t c = 25c t c = 100c i b = i c / 100 t p = 300 s, duty cycle < 2% tip120, tip121, TIP122 npn silicon power darlingtons 4 december 1971 - revised september 2002 specifications are subject to change without notice. maximum safe operating regions figure 4. thermal information figure 5. maximum forward-bias safe operating area v ce - collector-emitter voltage - v 10 10 100 1000 i c - collector current - a 01 10 10 100 sas120aa tip120 tip121 TIP122 dc operation t p = 300 s, d = 0.1 = 10% maximum power dissipation vs case temperature t c - case temperature - c 0 255075100125150 p tot - maximum power dissipation - w 0 10 20 30 40 50 60 70 80 tis120aa |
Price & Availability of TIP122 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |